Westcoat SC-35 Water-Based Concrete Stain | 1 Gallon
About
Westcoat SC-35 is ideal for adding translucent color to existing concrete and Westcoat’s Texture Crete®, ALX™ & MACoat™ systems. SC-35 can be used over acid stain too add highlight color.
SC-35 Water-Based Stain is a water-based color stain product. It is an easy one step way to stain safely. Unlike acid stains, there is no need for rinsing or neutralizing and there are no caustic ingredients. Available in 13 standard colors from natural earth tones to vibrant reds and blues. Colors can be blended to create custom colors.
Calculator
How many square feet is your project?
NOTE: Quantities given are based on an average coverage of 600 square feet per gallon. Consider decreasing the amount required if you are planning to dilute for lighter color saturation or increasing if your concrete surface is heavily profiled or absorbent.
Specs
- Package: 1-gallon and 5-gallon
- Coverage: 150-600 sf/gl over Westcoat cementitious systems and 600-1000 sf/gl over existing concrete
- VOC: <50 gm/l
- Shelf Life: 3 years in unopened container
SC-35 Armor - Safety Data Sheet
SC-35 Camel - Safety Data Sheet
SC-35 Camel - Safety Data Sheet
SC-35 Mahogany - Safety Data Sheet
SC-35 Olive - Safety Data Sheet
SC-35 Onyx - Safety Data Sheet
SC-35 Sahara - Safety Data Sheet
SC-35 Sepia - Safety Data Sheet
SC-35 Shale - Safety Data Sheet
SC-35 Sienna - Safety Data Sheet
SC-35 Umber - Safety Data Sheet
Instructions
Coverage
The coverage will vary depending on the surface and the overall desired look. For applications over Westcoat’s acrylic cements, coverage is approximately 150-600 square feet per gallon. For applications directly over concrete, coverage is approximately 600-1000 square feet per gallon. Product performs best if applied in thin even coats. For best results, filter prior to spraying.
Applying Product
Before beginning any project, it is recommended that a mock-up be installed to help indicate the overall look and finish. SC-35 can be applied on dry or slightly damp concrete or over acrylic cements. SC35 can be applied using a variety of methods, depending on the desired look and effect. SC-35 can be applied with: a pump sprayer, airless sprayer, pressure pot, gravity feed HVLP, sponge, brush, cotton rag or broom for application methods. For best results, a pump sprayer with a conical tip can be used to evenly distribute the stain. Straining or filtering the material before pouring into the sprayer, can help avoid clogging. Do not apply when temperatures are below 50F degrees or above 90F degrees. When temperatures are above 80F degrees, it may be necessary to dampen the surface prior to application, to prevent material from drying instantly. This product needs some wet time for the stain to properly penetrate the surface. Multiple colors may be applied at the same time for a variegated finish. Re-coat in ½ to 1 hour at 70F degrees, if needed. Stain is designed to be applied in one to two coats, depending on the overall look. Do not apply this material too thick, as it may affect the semi-transparent look and may prevent from proper penetration and adhesion.
See MoreWestcoat SC-35 Water-Based Concrete Stain | 1 Gallon
View Color Chart
SC-35 Water-Based Concrete Stain is an easy, one-step way to safely color concrete. There is no need for rinsing or neutralizing after placement and there are no caustic ingredients or fumes. Westcoat SC-35 Colors can even be blended to create custom colors.
- Water-based and low odor
- Easy and safe to use
- Can be applied over many other acrylic sealers
- Can be sealed with either solvent and water-based sealers
- Blend with each other to create custom colors
- No rinsing or neutralization required
About
Westcoat SC-35 is ideal for adding translucent color to existing concrete and Westcoat’s Texture Crete®, ALX™ & MACoat™ systems. SC-35 can be used over acid stain too add highlight color.
SC-35 Water-Based Stain is a water-based color stain product. It is an easy one step way to stain safely. Unlike acid stains, there is no need for rinsing or neutralizing and there are no caustic ingredients. Available in 13 standard colors from natural earth tones to vibrant reds and blues. Colors can be blended to create custom colors.
Calculator
How many square feet is your project?
NOTE: Quantities given are based on an average coverage of 600 square feet per gallon. Consider decreasing the amount required if you are planning to dilute for lighter color saturation or increasing if your concrete surface is heavily profiled or absorbent.
Specs
- Package: 1-gallon and 5-gallon
- Coverage: 150-600 sf/gl over Westcoat cementitious systems and 600-1000 sf/gl over existing concrete
- VOC: <50 gm/l
- Shelf Life: 3 years in unopened container
SC-35 Armor - Safety Data Sheet
SC-35 Camel - Safety Data Sheet
SC-35 Camel - Safety Data Sheet
SC-35 Mahogany - Safety Data Sheet
SC-35 Olive - Safety Data Sheet
SC-35 Onyx - Safety Data Sheet
SC-35 Sahara - Safety Data Sheet
SC-35 Sepia - Safety Data Sheet
SC-35 Shale - Safety Data Sheet
SC-35 Sienna - Safety Data Sheet
SC-35 Umber - Safety Data Sheet
Instructions
Coverage
The coverage will vary depending on the surface and the overall desired look. For applications over Westcoat’s acrylic cements, coverage is approximately 150-600 square feet per gallon. For applications directly over concrete, coverage is approximately 600-1000 square feet per gallon. Product performs best if applied in thin even coats. For best results, filter prior to spraying.
Applying Product
Before beginning any project, it is recommended that a mock-up be installed to help indicate the overall look and finish. SC-35 can be applied on dry or slightly damp concrete or over acrylic cements. SC35 can be applied using a variety of methods, depending on the desired look and effect. SC-35 can be applied with: a pump sprayer, airless sprayer, pressure pot, gravity feed HVLP, sponge, brush, cotton rag or broom for application methods. For best results, a pump sprayer with a conical tip can be used to evenly distribute the stain. Straining or filtering the material before pouring into the sprayer, can help avoid clogging. Do not apply when temperatures are below 50F degrees or above 90F degrees. When temperatures are above 80F degrees, it may be necessary to dampen the surface prior to application, to prevent material from drying instantly. This product needs some wet time for the stain to properly penetrate the surface. Multiple colors may be applied at the same time for a variegated finish. Re-coat in ½ to 1 hour at 70F degrees, if needed. Stain is designed to be applied in one to two coats, depending on the overall look. Do not apply this material too thick, as it may affect the semi-transparent look and may prevent from proper penetration and adhesion.
